|
|
新建网页 1
|
4 Layer Screen
Drying Cabinet |
| Screen drying
cabinet is an important tool in screen printing.
The screen
drying cabinet is needed by several procedures such as screen
degreasing, emulsion coating and hardener coating.
This machine gives up traditional
heating pipe technique to adopt advanced and safe
flat
carbon fiber heating plate.
Professional design, energy saving, safe and easy manipulation, used for
drying screen ,shading light, proofing dust and so on.
After being redesigned, this
cabinet has a smaller volume, will be cheaper and easier to ship than
the old type. Wooden case prevents the product from being damaged
*
Max size of screen frames of two
upper layers:23"x21"(58x55cm).
*
The screen frames need to be put
into the top layer in vertical direction.
*
Max size of screen frames of the two
lower layers::25"x23"(62x58cm).
|
| Featuress
Intelligent temp
controlling system. Its temp can be adjusted according to
the heat resistance of screen mesh. When the room temp is
77℉ (25℃), its highest temp can reach 126℉ (52℃).
The inside installed
axial flow fan makes the hot air circulate, which guarantees
an equal temp in cabinet and can improve drying efficiency
meanwhile. The axial flow fan (specially used for large
computer equipment) can normally be used for about 20,000
hours. It usually takes 2-4 minutes to well dry the screens
coated with the photosensitive emulsion.
It adopts a
hierarchical (100 levels) temp-adjusting system; users can
adjust temp according to ambient temperature and different
materials. It can operate according to your set temp next
time because of its automatic memorizing function.
It is wholly coated
without corrosion and rust. The drawer type is flexible but
perfect tight. All kinds of screens can be placed and moved
flatly with printed side up to guarantee the adhesive layer
smooth.
The heating plates
adopts the newest blade
and unit type, and achieves
double-heat, low
power and high heat efficiency. At the same time, it
guarantees that the temperature of the machine is
even to make the
temperature of each floor even and accurate.
Total power is
800W.compared with traditional 3000-8000W cabinet, this
machine can save power by70-90%.
Constructed by four
layers of cabinets,4 frames below 25”x21”(64x53) can
be held at the same time, saving time, improving efficiency.
Inner and outer sides all adopt electrostatic spraying,
professional outlook, easy to clean and no rust.
|
|
Voltage |
110V |
|
Power |
800W |
|
Plug standard
|
US, Canada |
|
Machine size |
27.9”x24”x12.2” (71x61x31cm)
|
|
Packing Size |
32.6"x27.9"x15.7" (83x71x40cm)
|
|
Net weight |
80Lb (36kg) |
|
Shipping weight
|
88Lb (40kg) |
Note: The
shipping cost is calculated by it's shipping volume.me. |
|
|
Instructions<
1. Turn on the
switch; then the machine will indicate “F000” and the air fan works
automatically.
2. Press “+”
to “F070’
3. Place
thermometer probe on the third drawer; Check the temp after five
minutes.
4. If the temp
does not meet your need, you can
press “+” or “-” to increase or reduce 10 grades; wait
five minutes and then check the temp.
5. After
adjusting the available temp, the machine will automatically save and
memorize
your set data.
6. It is normal
that the “F” and “O” displays alternately when the machine is working.
|
|
|
Reference data: When the room temperature is 77℉
(25℃)
or so, close and seal all drawers, ten minutes later after you have set,
the temp indicates —
1. Set “F050”,
the temp is about 93℉(34℃)
2. Set “F060”,
the temp is about 104℉ (40℃)
3. Set “F070”,
the temp is about 115℉ (46℃)
4. Set “F080”,
the temp is about 126℉ (52℃)
|
|
|
| Item include:de:
1 set 110V screen printing drying cabinet (006005)
|
|
