|
|
|
4
Heads Pneumatic Perfume Vacuum Filling Machine For Liquid |
Quadruplet-Head Liquid Filling Machine is the
vacuum-style semi-autimation filling machine, Mainly used for toilet
water, perfumers,liquid detergent, such as filling materials, it has a
way of measuring the performance level set, ligquid height can be
adjusted, the machine structure is compact and reasonable, Simple
opeartion ,easu maintenance, Parts and materials in contact with 304
stainless steel.
Applied to glass bottles and after
the vacuum is not easy deformation of the plastic bottles filling
containers |
|
|
| Constitute:
The product from the rack, filling head, lift pallets, to feed cans,
vacuum generator and feed, such as the composition of the trachea A)
Working Principle First, the feed tube and recovery of possession if
all material add the bucket filled with materials, filling the bottle at
the mouth, The bottle and move to the position on the board, filling
material and mouth bottle with tight seal, Began filling machine, been
deprived of because of the air bottle, and bottle is in a state of
negatiove pressure, liquid through the feed tube our from the bucket,
The first material from the filling moth filling tube (inside tube)
poured into the bottle, such as filling to set up a state level, Higher
than the vacuum bottle filler mouth(outside the tube) of the straw being
sucked out the liquid, return back to feed tank, at this point the state
of the bottle is filled. As tge liquid filling to set automatically
after the recovery of more than expected, to ensure that the height of
liquid bottle filling line, Do not have to consider whether the capacity
of the bottle |
|
|
Technical
parameters：
| Bottle height: |
≤250mm |
| Maxmum diameter if bottle |
≤35mm |
| Minimum diameter: |
≥4.5mm |
| Adjustable high-level(from the
bottle): |
15-50mm |
| Dimensions(not include the
resercoir bottle): |
660*470*1330mm |
| To adapt to the ambient
temperature: |
0-30℃ |
| Ventilation rate: |
5.5 liters/sec |
|
 |
| Installation
and Adjustment
1) The workplace must be
well-ventilated, clean environment.
2) In order to ensure a smooth
filling operation, the machine shoudl be the location of a solid
flat surface, shoud be four-wheel all the way.
3)Filling pallets before
landing a high degree of regulation in order to facilitate the
operation of the bottle filling. |
 |
|
| Operation
In the machine to adjust the
above-mentioned requirement, you can engage in normal work, The steps
are as followed:
1. Access to gas source
2. Air-condition switch, so that air
pressure gauge to reach
3. When its work is in the normal
state, the system reaches a certain negative pressire, allowed to carry
out the filling operation
4. Filling the bottle at the mouth
move, Pressed forward nursery school boards, bottle air suction vacuum
generators, Material from the feed tube flows through the filling mouth
bottle, and so on to set the surface after filling, higher than
the straw bottle of liquid material to be sucked back to feed tank. Can
be removed at this time have a good bottle filling, and into the bottle,
or bottle and then insert the second(third, fourth) mouth filling.
according to the abov-mentioned steps to filling.
5. Byadjusting the positioning the
first seal, Liquid height adjustable position.
6. Attention: Reach the surface after
filling the bottles should be taken away, will not long stand the bottle
on take-off and landing and in the filling state, Reach the surface
after filling, filling the mouth of each state shall not work more than
1 minutes. otherwise lead to mechanical failure or damage
 |
| Maintenance
1. Material should be no impurities
2. Filling the first open-house should
be ,maintained, no impurities plug, Filling the first opening to allow
dumping of cleaning, assembly is to be released. gaslet in
place(circle).
3. Periodoc inspection of one-way
value,Filling and sealing the first seal. damage shoould be found in the
relation for.
4.High by the bottle height adjustment
lifting pallets, Pallet should be flat, no skew.
5. Workplace must be well ventilated. |
|
 |
 |
|
Items included:
1 set of
4
Heads Pneumatic Perfume Vacuum Filling Machine For Liquid(021192)
 |
|
Item# |
Description |
QTY |
Unit |
Note |
|
021192 |
4
Heads Pneumatic Perfume
Vacuum Filling Machine For Liquid |
1 |
Set |
|
|
|
|
